-

Fri, 25 Oct 2024 23:51:12 +0200

Peter Krupa via *

peter@thepit.social

LMAO https://web.archive.org/web/20140310190221/http://www.sewingandembroiderywarehouse.com/embtrb.htm

Sat, 26 Oct 2024 17:24:46 +0200

_jayrope

jrp@hub.kliklak.net

@Peter Krupa Hilarious!

... the actual text:

"Embroidery Trouble Shooting Guide

Thread Breakage
Causes:
Improper Thread
Try re-threading the machine; make sure the thread goes through all guides.
Burrs
There may be burrs in the needle's eye, on the thread guides, needle plate or the hook. Replace the needle and try buffing the thread guides and needle plate. Buffing may alter the timing, so it's a good idea to replace a damaged hook.
Dry Hook
Because it dries out faster, the hook needs frequent lubrication. The hook assembly should be lubricated every 4-8 hours of machine running time.
Needle to small
You may have to change to a larger needle
Too much Adhesive spray
You should be using only Embroidery designed adhesive sprays, never over use them. Too much adhesive build up on the needle can cause them to drag and break threads. If this is happening you should examine the way you use your adhesive spray
Improper timing
If your machine isn't timed properly, it can cause many probems in addition to thread breaks. Such as broken needles, poor stitching or sometimes no stitching.
Old Thread
Thread can become brittle with age and long exposure to light, air and heat. You should store your thread in a cool, dark place to lengthen shelf life.
Bruised cone
A bruised cone of thread can occur if the thread falls on the floor, causing the lower winding of thread to loosen and catch as the thread spools off. You can take off the affected part of the thread or replace the cone.
Machine speed
Some of the designs increase the stress on thread. You should lower the machine speed as needed
Lint build up
A lint build up on the tension discs, needle plate or bobbin cases can cause breakage. These areas should be cleaned frequently with air or a brush.
Bent needle
This can happen after the needle hits a very hard object such as a Hoop, needle plate or the hook. If this happens you have to replace the needle and check for burrs and the timing.
Improper tensions
If the tension is too tight, it can cause pulling, puckering and thread stress. If the thread is too loose it can cause the thread to pile up and loop. You have to adjust the tensions to achieve a flat smooth look.
Using Tape for loose ends
Using tape can leave a residue and this can cause friction and thread breakage.
Holding the thread
If you hold the loose end of the thread when you start up the machine and you are pulling the thread too tight, it can cause the needle to bend or break and can also cause the thread to break.

Stitches form wrong or not at all
Causes:
Empty Bobbin
replace
Retaining finger in wrong position
loop can not form
Improper Timing
the bobbin hook won't catch the loop
Needle position is incorrect
can cause the timing to be off
Damaged hook
replace

Missed stitches
Causes:
Wrong Needle Size
in relation to the thread and this can make it difficult for loops to form
Thread is to tight or to loose
causes irregular loops to form
Timing is incorrect
can cause the bobbin hook to not catch the loop

Needle breaks
Causes:
Bent needle
replace
Dull needle
will bend and eventually break, replace
Timing wrong
damage to needle and hook and poor stitch quality
Holding thread during startup
can bend the needle and break the thread
Needle is inserted wrong
insert all the way up the needle bar shaft and needle screw is tight

Needle cuts holes in garment
Causes:
Dull needle
difficult to pierce garment causing tearing
Needle point is wrong type
wrong point can damage some fabrics, try a ballpoint
Needle to large
can stretch fabrics
Fabrics are to delicate
may have to use a topping

The design is out of register
Causes:
Garment is hooped to loosley
re-hoop but do not stretch fabric
The fabric is unstable
you may have to use a heavier backing

Garment is puckering
Causes:
Tensions to tight for a particular thread or garment
Improper hooping
Unstable fabric
Dull needles
Too many stitches in an area

These are some of the normal problems you may experience during the Embroidery Process."

Sent to the #Fediverse from a #Hubzilla instance.